How much does epoxy flooring cost in Dallas–Fort Worth?
Honest 2026 pricing for flake, metallic, MVB, and commercial epoxy systems in the DFW Metroplex. Every number on this page is grounded in what we actually quote on residential and commercial jobs across Dallas, Fort Worth, Plano, Frisco, Irving, Arlington, and the rest of the Metroplex.
Epoxy flooring cost per square foot in DFW
All ranges below include diamond grinding, proper surface prep, and our lifetime warranty. Prices are typical for jobs in the Dallas–Fort Worth Metroplex and may shift with slab condition and project size.
Flake (Chip) Epoxy
$7–$12 / sq ftMost popular residential system. Includes diamond grind, basecoat, broadcast flake, and two clear topcoats. Garages typically land near the low end; interior living spaces and patios trend higher.
Learn more about Flake (Chip) Epoxy →Metallic Epoxy
$12–$18 / sq ftDesigner 3D finish for showrooms, lobbies, and luxury garages. Pricing reflects mandatory moisture vapor barrier, multiple pigment layers, and slower cure schedule.
Learn more about Metallic Epoxy →Moisture Vapor Barrier (MVB)
$2.50–$4 / sq ft (add-on)Required on every Dallas–Fort Worth slab we coat. Prevents bubbling and delamination caused by Texas soil moisture. Already included in our metallic and flake quotes.
Learn more about Moisture Vapor Barrier (MVB) →Commercial / Industrial Epoxy
$8–$15 / sq ftWarehouses, automotive bays, retail, restaurants. Pricing depends on chemical-resistance requirements, slip rating, and downtime constraints.
Learn more about Commercial / Industrial Epoxy →Grind & Seal (Polished Concrete Look)
$5–$9 / sq ftBudget-friendly finish that exposes the concrete with a clear sealer. Best for warehouses and modern interiors that don't need the full epoxy build.
Learn more about Grind & Seal (Polished Concrete Look) →Driveway Flake Coating
$9–$14 / sq ftUV- and heat-stable system engineered for the Texas sun. Higher than interior flake because of outdoor-rated topcoats and surface prep on exposed slabs.
Learn more about Driveway Flake Coating →Serving the whole metroplex — see our Dallas epoxy flooring service area for cities covered and recent local projects.
What changes the price of your DFW epoxy floor?
Two garages of the same size can quote very differently. Here are the factors that move a Dallas–Fort Worth epoxy quote up or down.
- Slab condition — cracks, spalling, oil contamination, and old coatings all add prep time.
- Square footage — larger jobs spread mobilization costs and lower the per-foot rate.
- Moisture levels — Dallas–Fort Worth slabs almost always need an MVB to prevent failure.
- System buildup — number of coats, flake broadcast density, and topcoat type.
- Access & downtime — second-story garages, occupied retail, and night work add labor cost.
- Color/design complexity — multi-pigment metallics and custom logos take longer.
Why the cheapest DFW epoxy quote usually costs more long-term
Dallas–Fort Worth sits on expansive clay soils with constant moisture movement through concrete slabs. Crews that skip the moisture vapor barrier (MVB) to land a $3–$5/sq ft price almost always see those floors bubble, peel, or delaminate within 1–3 years.
Every Red Diamond Epoxy install includes an XPS grey-tinted MVB and a lifetime warranty against delamination — which is why our quotes start at $7/sq ft rather than $3.
Straight answers
How much does 1000 sq ft of epoxy cost?
A 1,000 sq ft epoxy floor in Dallas–Fort Worth typically costs $7,000–$12,000 for a full-broadcast flake system and $12,000–$18,000 for a designer metallic finish. Those numbers include diamond grinding, crack repair, a moisture vapor barrier, and the clear topcoat. Larger footprints drop the per-square-foot rate because mobilization and setup are spread across more area — a 1,000 sq ft commercial space usually prices closer to the bottom of the range than a 400 sq ft garage does.
How much does it cost to have someone epoxy your floor?
Professional installation runs $7–$12 per square foot for flake and $12–$18 per square foot for metallic in DFW, so a standard two-car garage lands around $3,500–$6,000. That price is mostly labor and preparation, not resin: diamond grinding the slab, chasing and filling cracks, testing moisture and installing a vapor barrier, then building the coating in layers over two to three days. Quotes under $5 per square foot are almost always a rolled-on kit with no grinding and no barrier.
What is the downside of epoxy flooring?
The honest downsides are UV yellowing, hot-tire pickup, and the fact that most failures are slab-prep failures rather than product failures. Standard epoxy topcoats amber in direct sunlight, which is why exterior and sun-exposed floors need a UV-stable aliphatic topcoat instead. Hot tires coming off a Texas highway can soften and lift an under-built or poorly bonded coating. And the biggest one: the overwhelming majority of epoxy floors that peel, bubble or delaminate do so because the concrete was not ground to the right profile or was never tested for moisture — not because epoxy is a bad material. Epoxy is also rigid, so it will telegraph a moving slab crack, and a full replacement means grinding the old system off rather than coating over it.
Are epoxy floors worth the money?
For most DFW homeowners, yes — a properly installed system lasts 15–20+ years, which works out cheaper per year than repainting a garage floor every two or three. You get a surface that resists oil, chemicals and hot tires, cleans with a mop, brightens the space considerably, and adds resale appeal in a market where finished garages are expected. It stops being worth it when you buy on price: a $3/sq ft coating over unprepared concrete will fail inside a few years and cost more to remove and redo than doing it once correctly.
DFW epoxy flooring FAQ
Real answers to the questions Dallas–Fort Worth homeowners and facility managers ask before booking an estimate.
What's the average cost of epoxy flooring in Dallas?
Most DFW homeowners spend $7–$12 per square foot for a quality flake system on a two-car garage, and $12–$18 per square foot for a designer metallic finish. Both prices include diamond grinding and a moisture vapor barrier.
Why is epoxy flooring more expensive in DFW than other markets?
Dallas–Fort Worth slabs sit on expansive clay soils that push moisture up through the concrete. A moisture vapor barrier is mandatory to prevent bubbling and delamination — this adds material and labor that many out-of-state quotes leave out.
Is cheap epoxy flooring worth it?
Quotes under $5 per square foot almost always skip diamond grinding and the MVB. Those floors typically fail within 1–3 years in the DFW climate, costing more to remove and redo than the original quality install.
How long does an epoxy floor installation take?
A standard two-car garage takes 2–3 days from grind to final topcoat. Metallic and larger commercial jobs typically run 3–5 days. You can walk on the floor the next morning and drive on it after 72 hours of cure.
How long does an epoxy floor last in the Texas climate?
A properly installed Red Diamond system with diamond grinding and an MVB lasts 15–20+ years residentially and is backed by our lifetime warranty against delamination. Cheap rolled-on coatings typically fail within 1–3 years in DFW heat and humidity.
Do I need to move everything out of my garage?
Yes — the slab needs to be fully cleared for diamond grinding and broadcast. We're happy to coordinate timing so you only have to clear it once, and many homeowners use the cure window to declutter or add storage racks.
Will epoxy crack or peel on my Dallas driveway?
Not when it's installed correctly. Our driveway flake system uses UV- and heat-stable topcoats engineered for direct Texas sun, plus the same diamond grind and prep we use indoors. Failed driveways are almost always rolled-on coatings without proper prep.
Do you offer free estimates?
Yes. We provide free on-site estimates across the Dallas–Fort Worth Metroplex, including a moisture reading, slab inspection, and a fixed written quote with our lifetime warranty.
What areas of DFW do you serve?
We cover the entire Dallas–Fort Worth Metroplex — Dallas, Fort Worth, Plano, Frisco, McKinney, Allen, Irving, Arlington, Southlake, Grapevine, Rockwall, and 30+ surrounding cities. There's no travel charge inside the Metroplex.
Still have questions? Get a free DFW estimate.
On-site moisture reading, slab inspection, and a fixed written quote backed by our lifetime warranty — no charge, no pressure.
Explore Red Diamond epoxy systems
Dive into the systems behind the pricing above, or see how we serve the Dallas–Fort Worth Metroplex.
READY TO TRANSFORM YOUR FLOOR?
Join many satisfied customers across DFW. Get your free consultation and see why Red Diamond Epoxy is the trusted choice for premium flooring.